Cell culture
Cell Confluency
Confluency decides when you passage, when you treat and how an assay behaves. It is also judged by eye, which makes it the least consistent number in cell culture.
Quick answer
Confluencyis the percentage of a culture vessel’s growth surface covered by cells. At 100 percent the cells form a continuous monolayer with no gaps. Most adherent lines are passaged at 70 to 90 percent and treated at a fixed, stated confluency, because density changes how cells respond. A confluent monolayer holds roughly 1 × 10⁵ cells per cm², so the cell number behind the same percentage differs with every plate format.
- Confluency measures area covered, not cells counted.
- Passage most adherent lines at 70 to 90 percent.
- Judge it across several fields, not one.
- State seeding density in protocols and use confluency as the check.
Estimating confluency by eye
Under the microscope you are judging coverage, not counting. The panels below show the same field at increasing coverage. Most people overestimate in the middle of the range, where scattered cells look busier than the area they actually occupy.
- Check several fields. Cells rarely spread evenly. Seeding, swirling and incubator vibration all push them toward the centre or the edge of a well.
- Use low magnification. At high power a sparse field looks crowded.
- Judge at the same time of day. A culture moves through several percent in a few hours while growing exponentially.
- Watch the edge wells. They evaporate faster and often lag the rest of the plate, as covered in common layout mistakes.
Cells in a confluent well, by plate format
Because confluency is a proportion, the cell number behind it scales with the growth area of the format. Taking a typical adherent line at about 1 × 10⁵ cells per cm²:
| Format | Growth area | Cells at 100% | Cells at 80% |
|---|---|---|---|
| 6-well | 9.6 cm² | 960 × 10³ | 768 × 10³ |
| 12-well | 3.8 cm² | 380 × 10³ | 304 × 10³ |
| 24-well | 1.9 cm² | 190 × 10³ | 152 × 10³ |
| 48-well | 1.1 cm² | 110 × 10³ | 88 × 10³ |
| 96-well | 0.32 cm² | 32 × 10³ | 26 × 10³ |
| 384-well | 0.056 cm² | 6 × 10³ | 4 × 10³ |
Indicative figures for a line of average size, such as HeLa or HEK293. Large or flat cells reach confluency at lower numbers, small or rounded ones at higher. Areas come from the surface area chart.
When to passage
The usual window is 70 to 90 percent. Below that you are splitting a culture that has not used its surface, and the next passage takes longer to recover. Above it, contact inhibition slows division, the medium exhausts faster and some lines begin to lift off in sheets.
A few cases differ. Lines that differentiate on contact, such as C2C12 or Caco-2, are often split well before 80 percent unless differentiation is the point. Primary cells and stem cells are usually kept sparser still. Suspension cultures have no surface to cover at all, so they are tracked by cells per millilitre instead.
Note the confluency at treatment on your plate map, next to the plate ID and date. When two runs disagree later, this is usually the variable that explains it.
Confluency and assay results
Density is not a cosmetic detail. Crowded cells divide more slowly, shift their metabolism, and often become less sensitive to a compound, which moves an IC50 without anything else changing. Sparse cells can be more fragile and give noisier replicates.
The practical fix is to work backwards. Decide the confluency you want on assay day, then seed the density that reaches it in the time available, using the figures in the table above. For a 96-well viability assay read at 48 hours, that usually means seeding a few thousand cells per well rather than aiming for confluency at plating.
Frequently asked questions
What does cell confluency mean?
Confluency is the percentage of the growth surface covered by cells. At 100 percent the monolayer touches edge to edge with no visible gaps. It describes area covered, not cell number, which is why the same percentage corresponds to very different totals in a 6-well and a 96-well plate.
What confluency should I passage cells at?
Most adherent lines are passaged at 70 to 90 percent, before the monolayer closes completely. Splitting earlier wastes growth time, and letting cells reach full confluency slows them down, changes their behaviour and, for some lines, triggers differentiation or detachment.
How do I estimate confluency by eye?
Look at several fields under low magnification and judge how much of the surface is covered, rather than counting cells. Compare against a reference chart, and always check more than one field, because cells crowd at the centre of a well or drift to the edges depending on how the plate was seeded and moved.
How many cells are in a confluent well?
For a typical adherent line, a confluent monolayer holds roughly 1 × 10⁵ cells per square centimetre. That means about 1 × 10⁶ cells in a confluent 6-well well, 32,000 in a 96-well well, and proportionally in between. Cell size changes this a lot, so count a test well before planning around it.
Does confluency affect assay results?
Yes, strongly. Cell density changes growth rate, metabolism, receptor expression and sensitivity to compounds, so the same treatment can give different results at 40 percent and 90 percent confluency. Fix a target confluency in your protocol and seed to reach it at the time of treatment, not at the time of plating.
What is the difference between confluency and cell density?
Confluency is a percentage of surface covered and is judged visually. Cell density is a number of cells per square centimetre or per millilitre, and it is measured by counting. Density is the reproducible one, which is why protocols should specify seeding density and use confluency as the check at the microscope.